moe
Bearing Changer
Reged: 01/11/05
Posts: 9824
Loc: Merritt Island, Fl
|
|
Installed mine today.
The instructions say you have to cut the wires then resolder. The oem indicators wire plugs will fit through the nut. The aftermarket ones, no. FYI...
--------------------
Blowing gravel off rural roads
|
Zmilin
Saddle Sore
Reged: 03/02/07
Posts: 5109
Loc: Sammamish, Washington - USA
|
|
Moe, good to know. Ill adjust/clarify the instructions ASAP.
Looks good! 
--------------------
07 Black BA, 39mm FCRs, TPUSA stage 1 head, TPUSA 813 cams, TPUSA 10.8:1 pistons, TTP #3 igniter, Specialty Spares Long Cannons, Tsukayu Hard Bags. 82HP/55tq
|
moe
Bearing Changer
Reged: 01/11/05
Posts: 9824
Loc: Merritt Island, Fl
|
|
To elaborate on the need to cut the turn signal wires, The oem plugs will slip though the oem turn signal's hollow bolt's nut. The Kellermann turn signals will not allow the oem connectors to pass through the Kellermann turn signals hollow bolts nuts.
I soldered on the oem connectors to the Kellermann turn signals and found out the hard way that those nuts are too small to allow the connectors through! Not on this install but when I fist installed them a ways back.
In summary, aftermarket turn signals may allow for the eom connectors to pass through, Kellermann turn signals, for sure, do not.
--------------------
Blowing gravel off rural roads
|
Zmilin
Saddle Sore
Reged: 03/02/07
Posts: 5109
Loc: Sammamish, Washington - USA
|
|
So that was a pretty good first run. Im down to one plate w/ tabs left and have placed the order for additional units.
Im going to look into powder coating later this week. Thing is Ill have to bend them all then have them coated, then drill the tab holes as needed. I don't know how that will effect the coating.
Thanks to everyone for their support and patronage. I hope my little product is up to standards and exceeding expectations.
--------------------
07 Black BA, 39mm FCRs, TPUSA stage 1 head, TPUSA 813 cams, TPUSA 10.8:1 pistons, TTP #3 igniter, Specialty Spares Long Cannons, Tsukayu Hard Bags. 82HP/55tq
|
Grzegorz
Freelance Jedi Knight
Reged: 09/03/05
Posts: 3582
Loc: Poland-Gdansk!!! UK-Oadby
|
|
easy to install half an hour job for everyone
--------------------
Grzegorz ......55 cubic inches 
http://www.flickr.com/photos/25172906@N06/ 904 Wiseco,813 TPUSA cams,TTP ignitor,gutted airbox,"breath" air intake,Keihin CR-S carbs,Black Epco exhaust,SS wheels
Edited by Grzegorz (03/12/11 10:06 AM)
|
FriarJohn
"Lighten up, Francis."
Reged: 01/11/05
Posts: 18825
Loc: East Helena, Montana
|
|
Zdenko Brackets Inc. has now gone International? Cool!
--------------------
BA.com Caretaker | Friarsride | jb.com
|
Zmilin
Saddle Sore
Reged: 03/02/07
Posts: 5109
Loc: Sammamish, Washington - USA
|
|
That looks much better than I expected! AWESOME! 
--------------------
07 Black BA, 39mm FCRs, TPUSA stage 1 head, TPUSA 813 cams, TPUSA 10.8:1 pistons, TTP #3 igniter, Specialty Spares Long Cannons, Tsukayu Hard Bags. 82HP/55tq
|
Grzegorz
Freelance Jedi Knight
Reged: 09/03/05
Posts: 3582
Loc: Poland-Gdansk!!! UK-Oadby
|
|
Quote:
That looks much better than I expected! AWESOME!
in real looks much better will do some pictures when will be out on bike.............I made a mock with full legal size plate that looked horrible 
--------------------
Grzegorz ......55 cubic inches
http://www.flickr.com/photos/25172906@N06/ 904 Wiseco,813 TPUSA cams,TTP ignitor,gutted airbox,"breath" air intake,Keihin CR-S carbs,Black Epco exhaust,SS wheels
|
Soren
Should be Riding
Reged: 01/12/05
Posts: 12034
Loc: Beaverton, OR
|
|
--------------------
•Triumph Connection
|
Zmilin
Saddle Sore
Reged: 03/02/07
Posts: 5109
Loc: Sammamish, Washington - USA
|
|
Damn... looks a bit wicked Soren!
--------------------
07 Black BA, 39mm FCRs, TPUSA stage 1 head, TPUSA 813 cams, TPUSA 10.8:1 pistons, TTP #3 igniter, Specialty Spares Long Cannons, Tsukayu Hard Bags. 82HP/55tq
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
